MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels Table of Contents INTRODUCTION ......................... 4 ..........................4 OTICE ...................... 4 ARNINGS AND AUTIONS ......................4 ATIONAL PPROVALS USER CONTROL LEVELS......................5 ........................5 EVEL EFINITION ......................... 5 ASSWORDS CONTROLS AND DISPLAYS ....................6 ........................
Page 3
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS LEVEL 3 PROGRAMMER FUNCTIONS...................24 LOG BOOK ..........................25 Table of Figures 1 – ZX1E, ZX2E C ................6 IGURE ONTROLS AND ISPLAYS 2 - ZX5E C ...................6 IGURE ONTROLS AND ISPLAYS 3 - S LED D ..................7...
Commissioning Manual (P/N 996-132) for information on programming and Level 3 functions. • The ZX1E, ZX2E and ZX5E Fire Alarm Control Panels are 1, 1-2 and 1-5 loop panels for use with analogue addressable devices from the following detector manufacturer ranges: - Apollo...
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS EN54-2 13.7 • The ZX1E, ZX2E & ZX5E range of panels has many features, which if used inappropriately, may contravene the requirements of EN54. Where such a EN54 Maximum of 512 possibility may arise, a suitable warning is given with brief details of the sensors / manual EN54 requirement and the relevant section it pertains to.
Program / Interactive Keys Zone LED Display Optional Zone LED Display Figure 1 – ZX1E, ZX2E Controls and Displays Figure 2 - ZX5E Controls and Displays Key Legend Symbol Function Sound Alarms Press to Turn on ALL Sounder Outputs (i.e. evacuate building manually).
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS Key Legend Symbol Function 0 to 9 Press to enter numbers 0-9 or letters A-J (N-W with Shift) > Press to scroll through fire alarms or faults manually on the display or letter K (X with Shift) <...
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels Indicator Colour Function How to Clear FIRE The panel has detected a fire alarm Correct the condition causing the condition, or the ‘Sound Alarms’ key alarm and then perform a panel has been pressed.
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS 3.3 Alphanumeric Display Indications • The alphanumeric liquid crystal display gives 80 characters of information on a 2-line display. The display is illuminated to assist viewing under dim ambient light conditions. • When the numeric keypad is not in use, the display will revert to automatically scrolling through any fire alarm or fault conditions present on the panel.
If more than one fire alarm condition is present, the alphanumeric display will either automatically scroll through or, can be manually scrolled through, the fire alarms registered. 4.3.1 Override Delays • If the ZX1E, ZX2E and ZX5E control panels are EN54-2 7.11d configured to operate with delays to outputs, a EN54...
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS 5 Level 2 Control Functions • All of the functions and operational features described for Level 1 user are available and are the same for a Level 2 user. • To enable Level 2 operation, press the SHIFT key. The display will then show:...
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels 5.2 Fault Conditions 5.2.1 Fault Indication • If the panel detects a fault, the FAULT LED is illuminated along with other appropriate system condition LED Indicators. The alphanumeric display gives detailed information regarding the nature of the fault and the panel buzzer will sound.
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS 5.4 User Option Functions [ACTIVE] 1)Commission 2)Test 3)Time 4)Enable 5)Disable 6)Print 7)View • The optional functions available to the user at Level 2 are as follows: Function Description Commission This option is not available to Level 2 users. It requires the entry of the Level 3 password before the programming mode can be entered.
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels 5.4.1 Test • To display the Test Menu, press ‘2’ and the display shows: 1)LEDs 2)LCD 3)Zones 4)Outputs 5)Audible Indicator • The test menu allows the user to test: The LED’s on the front panel display.
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS Test from zone? (Please key in number, then press “Enter”) • Key in the number of the first zone to be tested. For example, for zone 12, press ’12 ENTER’. • The display then prompts the last zone to be tested:...
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels 5.4.1.3.3 Inspecting Other Conditions During a Walk Test EN54-2 5.1 EN54 Display of • To inspect Fire, Fault or Disablement Conditions whilst a walk test is in functional progress, press the ‘>’ key. conditions: •...
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS RELAY OPERATED The onboard sounder circuits are constantly monitored for correct end-of-line termination. A sounder error will be reported if one of the sounders is left in the operated test state for more than 5 seconds.
Press ‘2’ and the display will prompt for the signalling loop circuit number where the device is located. Loop _ • Enter the required loop number (1 for ZX1E, 1-2 for ZX2E or 1-5 for ZX5E) and the display will prompt for the numeric address of the device: Loop 2...
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS • Enter the address of the device required. If the address is less than 3-digits long (for example address 34), this can be entered as either 034 or 34 followed by ENTER. • The display will then ask for confirmation (OK?).
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels 5.4.3.4 Enable or Disable Delayed Day Modes • The Delayed Day Mode operation is configured at Level 3 by the installer / maintenance contractor. • For example, the Delayed Day Mode may be set to be active between 8:00 and 17:00. Outside of these hours, a fire alarm condition will immediately sound the bells and activate outputs.
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS 5.4.3.5 Enable or Disable Outputs • All output devices (i.e. sounders and relays) can be disabled or enabled for test purposes. • To enable or disable an output device, press ‘5’ from the enable or disable menus.
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels 5.4.4 Print • To select the print menu, press ‘6’ from the user main, option menu. The display then shows: PRINT : 1)Devices 2)Events 5)Disabled 3)Mode 4)Setup • This menu controls the operation of the optional front panel printer on the ZX5E panel only. The user...
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS 5.4.5 View • To select the view menu, press ‘7’ from the user main, option menu. The display then shows: VIEW : 1)Devices 2)Log 5)Faults 4)Outputs 5)Disablements 6)Sys Events • This menu allows the user to view information about the selected option on the alphanumeric display.
7 Level 3 Programmer Functions • Refer to the Commissioning Manual (996-132) for complete information on commissioning and programming the ZX1E, ZX2E and ZX5E Fire Alarm Control Panels. Page 24 of 28 Document No. 996-130, Revision: 01, User Manual...
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS 8 Log Book • In accordance with best practice, the user should maintain a logbook to record all events resulting from or affecting the system. The logbook should be kept in a place accessible to authorized persons (preferably near the main panel.
MORLEY-IAS ZX2E/ZX5E Fire Alarm Control Panels EVENT DATA Date Time Counter Event Action Required Date Initials Reading Completed Table 7 - Logbook Event Data Page 26 of 28 Document No. 996-130, Revision: 01, User Manual...
Page 27
ZX2E/ZX5E Fire Alarm Control Panels MORLEY-IAS NOTES User Manual Document No. 996-130, Revision: 01, Page 27 of 28...